Description
The Teltonika TSW101 (TSW101000000) is a compact automotive PoE+ switch for vehicles that carry cameras, routers, or other Ethernet gear. It runs straight from a 12 V or 24 V vehicle battery, needs no configuration, and powers four devices over their Ethernet cables, so you skip extra power adapters and wiring in tight spaces.
Five Gigabit ports, a rugged anodized aluminum housing, and a -40 °C to 75 °C operating rating make it a practical fit for buses, service trucks, emergency vehicles, and mobile command units. Plug in your uplink, connect your devices, and wire it to vehicle power.
The Telecom Spot Take
The TSW101 is the switch we point customers to when a vehicle needs to power a few PoE cameras or access points without a separate injector or AC power. It is small, needs no setup, and is simple to wire. The key planning point is voltage: on a 24 V system you get a 60 W PoE budget, but on 12 V the total drops to 30 W. It is not ideal if you need VLANs, SFP uplinks, or more than four powered devices.
Key Features
- Four PoE+ output ports: Ports 1-4 deliver IEEE 802.3af/at (PoE and PoE+) power at 30 W per port, enough for IP cameras, access points, and other PoE devices in the vehicle.
- Battery-powered, no PSU needed: The 2-pin industrial DC socket accepts 9-30 VDC, so the switch connects directly to a 12 V or 24 V vehicle electrical system.
- PoE budget that follows your voltage: 60 W total on 24 VDC and 30 W total on 12 VDC. The switch does not cap output itself, so keep the combined load within that budget.
- Five Gigabit Ethernet ports: All ports run at 10/100/1000 Mbps with auto MDI/MDI-X, and port 5 serves as the uplink to your router or modem.
- Plug and play: No configuration needed. Connect the uplink, plug in devices, and apply power.
- Built for mobile installs: Anodized aluminum housing, IP30, -40 °C to 75 °C operating temperature, 5% to 95% non-condensing humidity, and a grounding screw.
- Vehicle and regional certifications: E-mark and UN ECE R10, plus FCC, IC (ISED), CE, UKCA, and RCM.
- Low standby draw: 0.64 W idle and 2.31 W max for the switch itself, so the switch itself adds little load to the vehicle battery.
Technical Specifications
| Specification | Detail |
|---|---|
| Brand / model | Teltonika TSW101 |
| Order code / SKU | TSW101000000 (standard package without power supply) |
| Switch type | Plug-and-play automotive PoE+ switch, no configuration needed |
| Ethernet | 5 x RJ45, 10/100/1000 Mbps, auto MDI/MDI-X: 4 x PoE out, 1 x uplink |
| IEEE standards | 802.3i, 802.3u, 802.3ab, 802.3x, 802.3az |
| PoE output ports | Ports 1-4; IEEE 802.3af (Type 1) and 802.3at (Type 2), Alternative A |
| PoE power per port | 30 W max (at PSE) |
| Total PoE budget | 60 W at 24 VDC; 30 W at 12 VDC (at PSE) |
| Power input | 2-pin industrial DC socket, 9-30 VDC (pin 1 power, red; pin 2 ground, black) |
| Power source | 12 V or 24 V vehicle battery; no additional power supply required |
| Power consumption | Idle 0.64 W; max 2.31 W (switch only); 62.3 W max with full PoE load |
| Switching performance | 10 Gbps non-blocking bandwidth; 128 KB packet buffer; 2K MAC address table; 9216-byte jumbo frames; cable detection |
| Max Ethernet cable length | 100 m |
| Status LEDs | 1 x power, 10 x Ethernet status (orange for 10/100 Mbps link, green for 1000 Mbps link) |
| Other | 1 x grounding screw |
| Housing | Anodized aluminum housing and panels; IP30 |
| Dimensions (W x H x D) | 115 x 32 x 95 mm |
| Weight | 384 g |
| Mounting | DIN rail, wall, or flat surface (each requires an additional kit) |
| Operating temperature | -40 °C to 75 °C |
| Operating humidity | 5% to 95% non-condensing |
| Certifications | E-mark, UN ECE R10, FCC, IC (ISED), Anatel, CE, UKCA, RCM, CB Scheme |
| Package box (W x H x D) | 175 x 35 x 150 mm |
| HS / HTS code | 851762 / 8517.62.00 |
What's in the Box
- TSW101 automotive PoE+ switch
- Quick Start Guide
This order code ships without a power supply because the switch is designed to run from vehicle power. Power wiring, mounting kits, and Ethernet cables are sold separately. Box contents can vary by order code, so ask us to confirm before you order if a specific accessory matters for your install.
Best For, Use Cases and Setup Tips
Best for: transit buses, police and fire vehicles, utility and service trucks, and mobile command units that need to power a handful of PoE cameras or access points from the vehicle battery.
Not ideal for: installs that need VLANs or other managed features, SFP fiber uplinks, more than four powered devices, AC-powered racks, or a total PoE load above 60 W.
- Budget by voltage: On a 12 V vehicle, plan for 30 W total across all PoE ports, such as two 15 W cameras. On 24 V, you can use the full 60 W, with no single port above 30 W.
- Wire it right: Connect your router or modem to port 5, PoE devices to ports 1-4, then wire the 2-pin socket (red to power, black to ground) and use the grounding screw.
- Check the PoE mode: The ports use PoE Alternative A, with power on pins 1-2 and 3-6. Confirm your powered devices accept 802.3af or 802.3at power.
- Read the LEDs: Green means a 1000 Mbps link, solid orange means a 10/100 Mbps link, and blinking orange shows active traffic.
- Need Profinet? Profinet Class A conformance is a separate order code (TSW101000001). This listing is the standard TSW101000000.
Comparison at a Glance
| Model | Copper ports | PoE budget | Uplinks | Input voltage |
|---|---|---|---|---|
| TSW101 | 5 x Gigabit (4 x PoE+) | 60 W at 24 VDC; 30 W at 12 VDC | Copper port 5 | 9-30 VDC |
| TSW200 | 8 x Gigabit PoE+ | 240 W | 2 x SFP | 9-57 V (44 V or higher for PoE) |
| TSW210 | 8 x Gigabit, no PoE | None | 2 x SFP | 9-57 V |
FAQ
Can the TSW101 run from a 12 V vehicle battery?
Yes. It accepts 9-30 VDC, so it works on 12 V and 24 V systems. On 12 V, the total PoE budget is 30 W; on 24 V it is 60 W.
Does TSW101000000 include a power supply?
No. This standard package ships without a power supply, since the switch is built to run from vehicle power through its 2-pin DC socket.
How many PoE devices can I power?
Four, on ports 1-4, at 30 W max per port. Keep the combined load within 60 W on 24 V or 30 W on 12 V, because the switch does not limit output.
Does it need any setup?
No. The TSW101 is plug and play with no configuration needed.
What automotive certifications does it have?
The TSW101 carries E-mark and UN ECE R10 certification, along with FCC, IC (ISED), CE, UKCA, and RCM.






